A new toy is on the SDR market @350 $PLUTO+SDR Transceiver , Gigabit Ethernet , Micro SDCard

Product Overview:

PLUTO+ is a software-defined radio platform that supports 2TX and 2RX, supports Gigabit Ethernet and Micro SD card. It refers to the design for well-known ADI ADALM-PLUTO and improves its shortcomings.

Features:

- ADC/DAC: AD9363 (Can hack to AD9361 or AD9364)

- 2 Transmit, 2 Receiving channeldru

- RF Range: 70MHZ~6GHZ

- Ref Clock: VCTCXO 40MHZ 0.5ppm

- SOC: for Zynq7010 FPGA: 28k

- RAM: 512M

- FLASH: 32M

- USB: 2.0, support OTG

- Ethernet: 1000Mb

- Micro SD can use to boot

- DC IN: 5V±0.5V-2A microUSB

Interfaces:

Please note that all IO levels are 1.8V.

3.1 When using the official firmware for ADI-PlutoSDR, please connect to URST-MI052.

3.2 When using Pluto+ firmware and need to support Ethernet, please connect URST-MIO46

3.3 When using SD card to boot, please connect SD-H to 1V8

3.4 When using JTAG to debug, please connect JTAG# to GND

3.5 Please connect EXCLK to GND when using external reference clock input

PTT Key Port:

- PTT drives optocouplers through GPIO0 (MI00), which requires an external relay or control circuit.

DFU KEY:

- At any time, you can press the DFU button and power on PLUTO+ again to enter the DFU mode, but you need to connect the URST jumper to MI052.

Ref CLK input IPEX:

- You can connect a cable to input an external high-precision reference clock for AD9363 through the IPEX interface.

- The main level should not exceed 3.3V, and the EXCLK jumper needs to be connected to GND to turn off the built-in clock

Calibrate the Frequency of Built-in VCTCXO:

- The frequency of the 40M clock can be fine-tuned by adjusting the adjustable resistor next to the VCTCXO, provided that you have a reference signal source.

Micro-SD:

Support booting via SD card, need to connect SD-H jumper to 1V8.

機翻?簡單校對:

SDR市場上有一個新玩具@ 350 $

PLUTO+ SDR收發器,千兆以網,microSD卡

產品概覽:

PLUTO+是一個軟件定義的無線電平臺,支持2 TX和2 RX,支持千兆以太網和微型SD卡.它指的是著名的ADI ADALM-PLUTO設計,改善了它的缺點,

特點:

- ADC / DAC: AD9363(可以改AD9361或AD9364)

-2傳輸,2接收頻道

-射頻范圍: 70 MHZ~ 6 GHZ

-參考時鐘: VCTCXO 40 MHZ 0.5 ppm

-SOC: Zynq7010 FPGA: 28 k

-內存: 512 M

-閃存: 32 M

-USB: 2.0,支持OTG

-以太網: 1000 Mb microSD可以用來啟動

-DC IN: 5±0.5V-2A microUSB

接口:

請注意,所有I0級別都是1.8 V.

3.1,使用ADI-PlutoSDR官方固件時,請連接URST-MI052.

3.2使用Pluto+固件需要支持以太網時,請連接URST-MIO46

3.3使用SD卡啟動時,請連接SD-H到1V8

3.4,使用JTAG調試時,請連接JTAG#GND

3.5,使用外部參考時鐘輸入請連接EXCL到GND

PTT鍵端口:

-PTT通過GPIOO (MI0O)驅動光耦合器,這需要外部繼電器或控制電路.

DFU關鍵:

-隨時隨地,你可以按下PLUTO+上的DFU按鈕和電源,進入DFU模式,但你需要連接URST跳轉到MI052.

參考CLK輸入IPEX:

-你可以通過IPEX接口連接一條電纜,輸入AD9363的外部高精度參考時鐘.主水平不應超過3.3 V, EXCLK跳轉器需要連接GND以關閉內置時鐘

校準內置VCTCXO頻率:

只要你有參考信號源,40 M時鐘的頻率可以通過調整VCTCXO旁邊的可調節電阻來微調,

MicroSD:

通過SD卡支持啟動,需要連接SD-H跳轉到1V8.